Welcome to HydrostreamForums.com
If you're not registered, please consider doing so. It's easy - just click the "Register" link at the top
right corner of the page. Our forum needs members like you to contribute to the site in order to survive.
We are a community of boat lovers and Hydrostream enthusiasts here; we are happy to help anyone
who may need advice or guidance for their 'Stream; and we encourage members to offer their advice
and guidance to others as well. Thank you for visiting our forums, and please register.
We're better than Facebook.
Registering only takes a few minutes and you can do so by CLICKING HERE
If you are a member, don't forget to log in to take full advantage of the forum.
If you're not registered, please consider doing so. It's easy - just click the "Register" link at the top
right corner of the page. Our forum needs members like you to contribute to the site in order to survive.
We are a community of boat lovers and Hydrostream enthusiasts here; we are happy to help anyone
who may need advice or guidance for their 'Stream; and we encourage members to offer their advice
and guidance to others as well. Thank you for visiting our forums, and please register.
We're better than Facebook.
Registering only takes a few minutes and you can do so by CLICKING HERE
If you are a member, don't forget to log in to take full advantage of the forum.
Prop Slip Calculator
How to find your propeller slip
This type of testing requires an experienced driver, good water conditions and enough room to not be a hazard to others or yourself. Take the time to become familiar with the handling characteristics of your boat before attempting a full speed run.
Where do you start? First, it is important to have accurate speed and RPM information. This is critical for the best results! If you are serious about getting the most performance out of your boat, invest in accurate instruments.
Think of a prop as screw. The pitch is the theoretical distance the prop should move through the water in 1 revolution. A 24" pitch prop would move 2 feet. The theoretical speed is figured by multiplying the pitch x engine rpm and dividing by (gear reduction x 12) = feet per minute. Divide by 5280 = Miles per minute, multiply x 60 = miles per hour. This can be shortened to (Pitch x RPM) / (Reduction x 1056) = MPH.
Slip is figured by comparing this theoretical speed to the actual measured speed. By the way, for these calculations, add 1" to the pitch if your prop is cupped. (Just about all hi-performance props are)
For the purpose of this test, we are looking for the absolute fastest boat speed. So trim the boat by the speedo! Assuming we are in the ball park, and do not have to worry about over revving the engines, ignore the tachs for the moment.
If this is your first test of a new package you do need to watch the RPM, and you might not be able to test at full throttle. DO NOT over rev. Check with your engine manufacturer for maximum RPM.
Without getting the boat so loose you lose control, open the throttle to full speed. Try increasing and lowering the trim until you find the fastest mph on your GPS or Speedo. Now look at the tach, and make notes of the trim position, rpm and speed. You can repeat this at any throttle setting or speed. In fact you may be more interested in your cruising speed than top end. The highest RPM is not necessarily the fastest speed !
Write your numbers down, maybe include notes as to weather, number of passengers, amount of fuel, etc. When you get back to the dock, pull out your trusty (or rusty if you are like me) calculator and do the following: Figure your theoretical speed from above, subtract you actual speed. Divide this difference by the actual speed. The number you get is your slip percentage.
Slip is never a negative number, and will range from 5% on a light cat to 25% on a heavy workboat. Most hi performance applications will be between 7 and 12 percent.
Use this calculator to figure out just about anything in regard to propeller, ratio, RPM and speed. You can change one parameter and recalculate the rest. Use the CalcT button to figure the theoretical speed from the actual speed and slip.
Back to the HydrostreamForums.com Knowledge Base
This type of testing requires an experienced driver, good water conditions and enough room to not be a hazard to others or yourself. Take the time to become familiar with the handling characteristics of your boat before attempting a full speed run.
Where do you start? First, it is important to have accurate speed and RPM information. This is critical for the best results! If you are serious about getting the most performance out of your boat, invest in accurate instruments.
Think of a prop as screw. The pitch is the theoretical distance the prop should move through the water in 1 revolution. A 24" pitch prop would move 2 feet. The theoretical speed is figured by multiplying the pitch x engine rpm and dividing by (gear reduction x 12) = feet per minute. Divide by 5280 = Miles per minute, multiply x 60 = miles per hour. This can be shortened to (Pitch x RPM) / (Reduction x 1056) = MPH.
Slip is figured by comparing this theoretical speed to the actual measured speed. By the way, for these calculations, add 1" to the pitch if your prop is cupped. (Just about all hi-performance props are)
For the purpose of this test, we are looking for the absolute fastest boat speed. So trim the boat by the speedo! Assuming we are in the ball park, and do not have to worry about over revving the engines, ignore the tachs for the moment.
If this is your first test of a new package you do need to watch the RPM, and you might not be able to test at full throttle. DO NOT over rev. Check with your engine manufacturer for maximum RPM.
Without getting the boat so loose you lose control, open the throttle to full speed. Try increasing and lowering the trim until you find the fastest mph on your GPS or Speedo. Now look at the tach, and make notes of the trim position, rpm and speed. You can repeat this at any throttle setting or speed. In fact you may be more interested in your cruising speed than top end. The highest RPM is not necessarily the fastest speed !
Write your numbers down, maybe include notes as to weather, number of passengers, amount of fuel, etc. When you get back to the dock, pull out your trusty (or rusty if you are like me) calculator and do the following: Figure your theoretical speed from above, subtract you actual speed. Divide this difference by the actual speed. The number you get is your slip percentage.
Slip is never a negative number, and will range from 5% on a light cat to 25% on a heavy workboat. Most hi performance applications will be between 7 and 12 percent.
Use this calculator to figure out just about anything in regard to propeller, ratio, RPM and speed. You can change one parameter and recalculate the rest. Use the CalcT button to figure the theoretical speed from the actual speed and slip.
Back to the HydrostreamForums.com Knowledge Base