Wondering how to post images or maybe change your avatar or maybe something else?
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.
To visit the HydrostreamForums Knowledge Base CLICK HERE
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.
To visit the HydrostreamForums Knowledge Base CLICK HERE
Tach not working
Tach not working
I have a 84 V-King with an Evinrude V4 140 stamped 83 production. I have replaced the tach and also the voltage reg without success. I do not have the repair manual and was hoping to solve this with some help on here.
John
John
-
- Site Admin
- Posts: 3974
- Joined: Mar 25, 2009 7:31 pm
- Location: Nowthen, MN
- Has thanked: 351 times
- Been thanked: 82 times
- Contact:
Re: Tach not working
I cant help ya much as I am not that savvy with the electronics on the motors but I do have a service manual that someone sent to me that I uploaded to my server if you like. It has helped me alot big time in getting a few things on my 175 taken care.
Just right click the link then select save target as or save link as.
http://www.hippie459mn.com/downloads/1973-1989_Johnson_Evinrude_Outboard_Service_Manual_48-235_Hp.pdf
Hope that helps some.
Just right click the link then select save target as or save link as.
http://www.hippie459mn.com/downloads/1973-1989_Johnson_Evinrude_Outboard_Service_Manual_48-235_Hp.pdf
Hope that helps some.
-Kevin
Project Vulture | Project Vector | Project Vamp | Project Vixen
The Vulture Wish List | Project CobraJet
1977 HydroStream Vulture - Worlds longest ongoing project.
1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
1976 Pontoon - aka The Family Truckster
Project Vulture | Project Vector | Project Vamp | Project Vixen
The Vulture Wish List | Project CobraJet
1977 HydroStream Vulture - Worlds longest ongoing project.
1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
1976 Pontoon - aka The Family Truckster
-
- HSF Supporting Vendor
- Posts: 1989
- Joined: Mar 29, 2009 11:38 pm
- Location: montgomery MN
- Contact:
Re: Tach not working
Check continuity on your gray wire from the volt regulator to the back of your gauge.
Check for power on your purple wire and a ground on your black.
Did you change anything or did your tack just quit working?
Check for power on your purple wire and a ground on your black.
Did you change anything or did your tack just quit working?
Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Re: Tach not working
77Viper,
I have learned on my motor the lead for the tach comes off the rectifier. The voltage reg has a yellow wire that goes to terminal one of the strip and the purple wire goes to the terminal six. The yellow wire from the rectifier goes to the terminal which connects to the grey wire that goes to the control box.
I have learned on my motor the lead for the tach comes off the rectifier. The voltage reg has a yellow wire that goes to terminal one of the strip and the purple wire goes to the terminal six. The yellow wire from the rectifier goes to the terminal which connects to the grey wire that goes to the control box.
-
- HSF Supporting Vendor
- Posts: 1989
- Joined: Mar 29, 2009 11:38 pm
- Location: montgomery MN
- Contact:
Re: Tach not working
Ok I was wrong and thought the signal came from the reg. but it makes more sence if it came off the rectifier. I have a hard time not seeing these things as I don't work on that many motors from the 80's. I would still check for continuity on the gray to the rectifier.
Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Re: Tach not working
I believe I have a bad rectifier... Checked it with an ohm meter.. Will have a new rectifier by the weekend
-
- HSF Supporting Vendor
- Posts: 1989
- Joined: Mar 29, 2009 11:38 pm
- Location: montgomery MN
- Contact:
Re: Tach not working
After a new tach that would be my guess. I hope it works.
Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Re: Tach not working
well, still no tach.... must be some bad wiring... Anyone know what the voltage is at the input for the tach?? I know i have voltage drop from the control box vs the tach input
-
- HSF Supporting Vendor
- Posts: 1989
- Joined: Mar 29, 2009 11:38 pm
- Location: montgomery MN
- Contact:
Re: Tach not working
What is your voltage on your purple wire? should be 12 volts
Do you have a good ground on your black?
The gray is ac voltage, I'm not sure off hand what it is.
Do you have continuity on gray all the way back to the motor?
Do you have a good ground on your black?
The gray is ac voltage, I'm not sure off hand what it is.
Do you have continuity on gray all the way back to the motor?
Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
-
- Random Topics
- Replies
- Views
- Last post
-
- 2Replies
- 58473 Views
- Last post by Hippie459MN
Aug 22, 2021 12:46 pm
-
- 3Replies
- 51482 Views
- Last post by tnelson77
Sep 22, 2021 8:27 pm
-
- 2Replies
- 48570 Views
- Last post by idvette
Aug 30, 2021 12:21 pm
-
- 39Replies
- 244133 Views
- Last post by Hippie459MN
Jan 06, 2023 1:17 pm
-
- 5Replies
- 66847 Views
- Last post by tnelson77
Sep 22, 2021 8:27 pm
Who is online
Users browsing this forum: No registered users and 3 guests