Wondering how to post images or maybe change your avatar or maybe something else?
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.
To visit the HydrostreamForums Knowledge Base CLICK HERE
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.
To visit the HydrostreamForums Knowledge Base CLICK HERE
my 09 homebuilt ( stealth )
-
- Getting my feet wet
- Posts: 58
- Joined: Oct 18, 2010 8:56 pm
- Location: Oriental , North Carolina / near New bern , nc
- Contact:
Re: my 09 homebuilt ( stealth )
Hydro 76
Good topics and thankyou greatly for the comploment . the dash / does go up to the window ( sheild ) it did allow a little more room for gauges / electronics .
It seems i have heard of blue printing a bottom before , it's a very delicate thing , even heard of a man that largly modified his his pad and it caused the boat to climb to high and over at 72 causing some seriouse ingeries . As to the sharpend edges / seems to me that it would have to help ! As to the pad / i just watched a vid the other day on utube were a man heavely cuped his pad , yet the pad is not thick enough to dish it out , so looks like he had build the outer edges and would cause the boat to ride even higher .... i think to watch the vid of the boat it acts radical up there !
Alot of the actual drag boats have taken there windsheilds off to reduce drag/ yet it was designed that way to give down force ... back in the days when these boats were made they didn't have motors like they have today just to bold up to the back and not only that but the hulls were only designed to go around 70mph .
The boat i have modified ... is way too heavy because of the pre existing materials of the late 70's ...and is being treated and faired as a prototype in order to build a NICE plug off of it ... I'm thinking boat number 1 out of the mold will be hand layed carbon/kevlar and should allow for very impressive weight ! what if our boats were 800 - 1,000 lbs lighter ...
[album][/album]
balist placement of fuel cell and batteries
Good topics and thankyou greatly for the comploment . the dash / does go up to the window ( sheild ) it did allow a little more room for gauges / electronics .
It seems i have heard of blue printing a bottom before , it's a very delicate thing , even heard of a man that largly modified his his pad and it caused the boat to climb to high and over at 72 causing some seriouse ingeries . As to the sharpend edges / seems to me that it would have to help ! As to the pad / i just watched a vid the other day on utube were a man heavely cuped his pad , yet the pad is not thick enough to dish it out , so looks like he had build the outer edges and would cause the boat to ride even higher .... i think to watch the vid of the boat it acts radical up there !
Alot of the actual drag boats have taken there windsheilds off to reduce drag/ yet it was designed that way to give down force ... back in the days when these boats were made they didn't have motors like they have today just to bold up to the back and not only that but the hulls were only designed to go around 70mph .
The boat i have modified ... is way too heavy because of the pre existing materials of the late 70's ...and is being treated and faired as a prototype in order to build a NICE plug off of it ... I'm thinking boat number 1 out of the mold will be hand layed carbon/kevlar and should allow for very impressive weight ! what if our boats were 800 - 1,000 lbs lighter ...
[album][/album]
balist placement of fuel cell and batteries
-
- HSF Supporting Vendor
- Posts: 1989
- Joined: Mar 29, 2009 11:38 pm
- Location: montgomery MN
- Contact:
Re: my 09 homebuilt ( stealth )
I sharpened all the edges on my viper bottom and made sure it was still pefectly straight.
My viper weighs 997 fully rigged but without gas, I'm hopeing to be lighter with the vking.
My viper weighs 997 fully rigged but without gas, I'm hopeing to be lighter with the vking.
Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
-
- Getting my feet wet
- Posts: 58
- Joined: Oct 18, 2010 8:56 pm
- Location: Oriental , North Carolina / near New bern , nc
- Contact:
Re: my 09 homebuilt ( stealth )
That's awesome ... i don't know much about the Viper's but you should be screaming with those kind of weight to horse power numbers .
Seems like with that motor and a 130 shot if nos doesnt that put you around 370 horse power , ahh that's pretty strong ! If you don't mind saying , what kind of gps top end numbers are you showing .
Either way , you must be having a ball , i sough on here were you blew away the big v-8 in board ...LOL loven it
Check this out , been hidden it for 7 yrs now and it's a true 300oc block 20 "ocean mid and low water pickup ( 1985 )
[album][/album]
Seems like with that motor and a 130 shot if nos doesnt that put you around 370 horse power , ahh that's pretty strong ! If you don't mind saying , what kind of gps top end numbers are you showing .
Either way , you must be having a ball , i sough on here were you blew away the big v-8 in board ...LOL loven it
Check this out , been hidden it for 7 yrs now and it's a true 300oc block 20 "ocean mid and low water pickup ( 1985 )
[album][/album]
-
- Getting my feet wet
- Posts: 58
- Joined: Oct 18, 2010 8:56 pm
- Location: Oriental , North Carolina / near New bern , nc
- Contact:
Re: my 09 homebuilt ( stealth )
This is an old pick of the previouse owner out of More Head city , NC / J T Bried of 70 west marina drag raced this old hull for years . ...[album][/album]
Last edited by 19'stealth2009 on Jan 17, 2011 6:14 am, edited 1 time in total.
-
- HSF Supporting Vendor
- Posts: 1989
- Joined: Mar 29, 2009 11:38 pm
- Location: montgomery MN
- Contact:
Re: my 09 homebuilt ( stealth )
I'm not sure how much the 3.6 weighs but I know it's a bunch more than your 2.5. Your Stealth looks like it rides fairly high in the back compared to a stock stream but I still would do some testing before putting it on.
The viper and vector are very similar the only difference is the bow, the bottom is the same.
My motor is a fairly stock 2.4 200, just tight heads, reeds, and carbs so I would say a honest 340 horse motor. I'm not into top end but did take it up to 101.7 once with a 30 pitch. It will do 97 in the quarter mile with a 26 yamaha.
The viper and vector are very similar the only difference is the bow, the bottom is the same.
My motor is a fairly stock 2.4 200, just tight heads, reeds, and carbs so I would say a honest 340 horse motor. I'm not into top end but did take it up to 101.7 once with a 30 pitch. It will do 97 in the quarter mile with a 26 yamaha.
Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
-
- Getting my feet wet
- Posts: 58
- Joined: Oct 18, 2010 8:56 pm
- Location: Oriental , North Carolina / near New bern , nc
- Contact:
Re: my 09 homebuilt ( stealth )
just finished my newest style front wind SHEILD check it out guy's ![album][/album]
[album][/album]
[album][/album]
-
- Site Admin
- Posts: 3978
- Joined: Mar 25, 2009 7:31 pm
- Location: Nowthen, MN
- Has thanked: 352 times
- Been thanked: 82 times
- Contact:
Re: my 09 homebuilt ( stealth )
I really like that. Any shots of the dash?
[ Post made via Mobile Device ]
[ Post made via Mobile Device ]
-Kevin
Project Vulture | Project Vector | Project Vamp | Project Vixen
The Vulture Wish List | Project CobraJet
1977 HydroStream Vulture - Worlds longest ongoing project.
1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
1976 Pontoon - aka The Family Truckster
Project Vulture | Project Vector | Project Vamp | Project Vixen
The Vulture Wish List | Project CobraJet
1977 HydroStream Vulture - Worlds longest ongoing project.
1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
1976 Pontoon - aka The Family Truckster
-
- HSF Supporting Vendor
- Posts: 1989
- Joined: Mar 29, 2009 11:38 pm
- Location: montgomery MN
- Contact:
Re: my 09 homebuilt ( stealth )
Nice work it looks great!
Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
-
- Getting my feet wet
- Posts: 58
- Joined: Oct 18, 2010 8:56 pm
- Location: Oriental , North Carolina / near New bern , nc
- Contact:
Re: my 09 homebuilt ( stealth )
Thankyou for the comploments , they are always nice to hear because they certainly help to keep me motivated .
I can post some pics of the dash later on this week , i have all the guages hanngin out of the dash trying to get them all wired up now . The new hem will be here tuesday and maybe i can get it all done this week (night's) .
Thanks agian
I can post some pics of the dash later on this week , i have all the guages hanngin out of the dash trying to get them all wired up now . The new hem will be here tuesday and maybe i can get it all done this week (night's) .
Thanks agian
Last edited by 19'stealth2009 on Jan 17, 2011 6:16 am, edited 1 time in total.
-
- Random Topics
- Replies
- Views
- Last post
-
- 2Replies
- 5410 Views
- Last post by aaron78viper
Oct 09, 2017 9:14 am
-
-
v king windshield side mounting screws something that looks better
Last post by mitchielpricer « Jul 27, 2016 7:26 pm - 1Replies
- 11514 Views
- Last post by mitchielpricer
Jul 27, 2016 7:26 pm
-
-
- 4Replies
- 7183 Views
- Last post by AdamDK
Aug 12, 2016 11:43 am
-
- 1Replies
- 5878 Views
- Last post by Treebeard
Aug 13, 2016 6:57 pm
-
- 3Replies
- 6836 Views
- Last post by alaskastreamin
Sep 16, 2016 12:43 pm
Who is online
Users browsing this forum: No registered users and 5 guests