I don't think you will see a dramatic increase in speed being it's not too far off now. But with a combination of things you will hit 80.
What rpm's are you seeing with your props?
A cheap hp increase is in cutting your heads to 35cc and bumping timing up to 25 degrees, you will need to run fresh 91 octane gas.
Welcome to HydrostreamForums.com
If you're not registered, please consider doing so. It's easy - just click the "Register" link at the top
right corner of the page. Our forum needs members like you to contribute to the site in order to survive.
We are a community of boat lovers and Hydrostream enthusiasts here; we are happy to help anyone
who may need advice or guidance for their 'Stream; and we encourage members to offer their advice
and guidance to others as well. Thank you for visiting our forums, and please register.
We're better than Facebook.
Registering only takes a few minutes and you can do so by CLICKING HERE
If you are a member, don't forget to log in to take full advantage of the forum.
If you're not registered, please consider doing so. It's easy - just click the "Register" link at the top
right corner of the page. Our forum needs members like you to contribute to the site in order to survive.
We are a community of boat lovers and Hydrostream enthusiasts here; we are happy to help anyone
who may need advice or guidance for their 'Stream; and we encourage members to offer their advice
and guidance to others as well. Thank you for visiting our forums, and please register.
We're better than Facebook.
Registering only takes a few minutes and you can do so by CLICKING HERE
If you are a member, don't forget to log in to take full advantage of the forum.
Vulture setup
Re: Vulture setup
Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
-
- The new guy
- Posts: 8
- Joined: Apr 29, 2010 3:03 pm
Re: Vulture setup
Right now with the 24 Trophy I am turning 6800-6900. The results have varied some with the other props. The 26 re3 was turning 6500 or so. 6800 with one Yamaha drag in a 24" 7200 with another. But mostly I just lose topend with all the other props I have tried. I gain lots of bottom end but I am not drag racing, just looking for that elusive larger number. Thanks, Dwayne.
[ Post made via Mobile Device ]
[ Post made via Mobile Device ]
-
- The new guy
- Posts: 8
- Joined: Apr 29, 2010 3:03 pm
Re: Vulture setup
I got my 6" set back plates installed between the transom and hydraulic plate. Going to stop tomorrow on the way to the river and level boat and propshaft so I can adjust my height. Hopefully it help the boat free up and run a little better. I should have something to post in a day or two on the outcome of the longer offset. Dwayne.
[ Post made via Mobile Device ]
[ Post made via Mobile Device ]
-
- Site Admin
- Posts: 3991
- Joined: Mar 25, 2009 7:31 pm
- Location: Nowthen, MN
- Has thanked: 358 times
- Been thanked: 83 times
- Contact:
Re: Vulture setup
Can't wait to hear how it goes.
[ Post made via Mobile Device ]
[ Post made via Mobile Device ]
-Kevin
Project Vulture | Project Vector | Project Vamp | Project Vixen
The Vulture Wish List | Project CobraJet
1977 HydroStream Vulture - Worlds longest ongoing project.
1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
1976 Pontoon - aka The Family Truckster
Project Vulture | Project Vector | Project Vamp | Project Vixen
The Vulture Wish List | Project CobraJet
1977 HydroStream Vulture - Worlds longest ongoing project.
1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
1976 Pontoon - aka The Family Truckster
-
- The new guy
- Posts: 8
- Joined: Apr 29, 2010 3:03 pm
Re: Vulture setup
Well, I made it to the river today and did a little testing. The extensions didn't increase my speed yet, but did make the boat drive better. Now to more or less start over with props and setup.
[ Post made via Mobile Device ]
[ Post made via Mobile Device ]
-
- Getting my feet wet
- Posts: 32
- Joined: Mar 12, 2017 12:57 pm
- Location: Mathews, VA
- Has thanked: 1 time
Re: Vulture setup
Bumping this up. What did you end up doing for setup and prop?
[ Post made via Android ]
[ Post made via Android ]
Re: Vulture setup
Hey everyone, figure ill add to this thread instead of starting a new one, I just sold my viper this past weekend and picked up a Vulture (I'd like to see my 40's). Took the boat out and it drives like a dream compared to "the death trap" as my friends liked to call it. The boat has a 77' 200 johnson on it right now and plan to keep it for a few years and build up a nice 2.5 for it. In the meantime I'd like to get everything I can out of what I have. I would like to get the motor moved back before I start messing with height and prop combos but not sure where to start. I have read everything from 6" to 12+"' for these boats. Just looking for a place to start. Any advice would be greatly appreciated. Thanks.
-
- Random Topics
- Replies
- Views
- Last post
-
- 1Replies
- 11239 Views
- Last post by Hippie459MN
Apr 28, 2016 9:59 pm
-
- 12Replies
- 8590 Views
- Last post by Hippie459MN
Oct 23, 2016 11:27 am
-
- 10Replies
- 13951 Views
- Last post by RussF
Jun 29, 2016 5:34 pm
-
- 2Replies
- 4902 Views
- Last post by RussF
Jul 13, 2016 4:26 pm
-
- 1Replies
- 11425 Views
- Last post by Justarobb
Jul 07, 2016 8:14 am