Wondering how to post images or maybe change your avatar or maybe something else?
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.
To visit the HydrostreamForums Knowledge Base CLICK HERE
You can find that and a lot of other useful tips for using the forums in the HydrostreamForums Knowledge Base.
To visit the HydrostreamForums Knowledge Base CLICK HERE
HELP!! What am i looking at??
-
- Getting my feet wet
- Posts: 55
- Joined: Mar 30, 2012 8:04 pm
- Location: New Munich, MN
- Contact:
HELP!! What am i looking at??
i took the carpet out and found a poorly cut piece of plywood and removed it to find all this underneath....what am i even looking at? I need help knowing what im dealing with here.
[ Post made via Android ]
[ Post made via Android ]
[ Post made via Android ]
[ Post made via Android ]
- Attachments
-
- T2012-04-03_21-23-29_311-1.jpg (196.69 KiB) Viewed 3899 times
-
- Getting my feet wet
- Posts: 55
- Joined: Mar 30, 2012 8:04 pm
- Location: New Munich, MN
- Contact:
Re: HELP!! What am i looking at??
[ Post made via Android ]
- Attachments
-
- H2012-04-03_21-23-40_139-1.jpg (224.76 KiB) Viewed 3898 times
-
- Hydrostream know it all
- Posts: 997
- Joined: Nov 20, 2009 11:35 pm
- Location: Pleasant Prairie, WI
- Been thanked: 2 times
- Contact:
Re: HELP!! What am i looking at??
Looks to me like some really bad rotted core, but it's hard to tell from the picture. Is there another layer of glass, then rot, then the hull? If it is rotted core, you will be glad it is that bad. It sucks if it is half good. Hard to remove. If you can, do the bow and rear before the middle first. JMO. Bill
-
- Hydrostream know it all
- Posts: 997
- Joined: Nov 20, 2009 11:35 pm
- Location: Pleasant Prairie, WI
- Been thanked: 2 times
- Contact:
Re: HELP!! What am i looking at??
Your looking at a lot of grinding and Fiberglas work. Really that's the core that's rotten underneath the Fiberglas, you'll have to rip all the glass up and most probley just sweep the reminats of the core up. You can go to Chet's thread when he did his viper and see what his looked like and what it took to repair his
[ Post made via iPhone ]
[ Post made via iPhone ]
81 Varmint 2.5 Mag 3
82 Vandal Merc 85
76 Viper Merc 150
84 Valero
82 Vandal Merc 85
76 Viper Merc 150
84 Valero
-
- HSF Supporting Vendor
- Posts: 1989
- Joined: Mar 29, 2009 11:38 pm
- Location: montgomery MN
- Contact:
Re: HELP!! What am i looking at??
Since the previous owner was driving it I didn't think it was that bad but it NEEDS to be replaced. Like Bill said it will be a lot easier to remove since it is all rotten I would guess you can have it out in a weekend easy. My computer isn't playing nice but I will post a pic of a good core.
This is what is should look like. Granted this is new clean glass over the balsa but you get the point.
If it's too much for you and you want to trade back I am willing.
This is what is should look like. Granted this is new clean glass over the balsa but you get the point.
If it's too much for you and you want to trade back I am willing.
Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
-
- Getting my feet wet
- Posts: 55
- Joined: Mar 30, 2012 8:04 pm
- Location: New Munich, MN
- Contact:
Re: HELP!! What am i looking at??
I think its all rotten really bad...and the fiberglass on the floor is cracked through and it all just looks like a big mess. How do i know what to remove and when i get to the bottom?
[ Post made via Android ]
[ Post made via Android ]
-
- HSF Supporting Vendor
- Posts: 1989
- Joined: Mar 29, 2009 11:38 pm
- Location: montgomery MN
- Contact:
Re: HELP!! What am i looking at??
The top layer should rip out, then there will be a void where the core was stop there.
Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
-
- Getting my feet wet
- Posts: 55
- Joined: Mar 30, 2012 8:04 pm
- Location: New Munich, MN
- Contact:
Re: HELP!! What am i looking at??
Ok, is there any less costly method to make it safe again or is about $1500 just what it takes?
[ Post made via Android ]
[ Post made via Android ]
-
- HSF Supporting Vendor
- Posts: 1989
- Joined: Mar 29, 2009 11:38 pm
- Location: montgomery MN
- Contact:
Re: HELP!! What am i looking at??
That is a safe budget for the job, it can be done for a little less but if you plan for $1500 and only spend $1000 you are in a better position. It can be more if you start using composites and epoxy.
One thing to consider is after it's done you can put just about any power on it you want and be relatively safe.
One thing to consider is after it's done you can put just about any power on it you want and be relatively safe.
Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
-
- Random Topics
- Replies
- Views
- Last post
-
- 4Replies
- 80999 Views
- Last post by alaskastreamin
Feb 22, 2019 11:52 am
-
- 17Replies
- 172168 Views
- Last post by AdamDK
Dec 13, 2019 7:07 pm
-
- 2Replies
- 69645 Views
- Last post by Hippie459MN
Feb 24, 2019 10:11 am
-
-
Does anyone know of any Hydrostream emblems or decals available?
Last post by Shawnv-king « Mar 05, 2019 8:47 pm - 5Replies
- 88420 Views
- Last post by CleanV-King
Dec 29, 2020 11:32 pm
-
-
- 4Replies
- 79239 Views
- Last post by dehydrated
Mar 08, 2019 11:15 am
Who is online
Users browsing this forum: No registered users and 48 guests