I just finished my viper and will be playing with set up in the near future Here is where I'm starting from.
77 viper with factory hook and pad
The hull weighs 997 rigged dry center steer
20" mid on a bob's convertible jack plate set at 2.5"
I have a 3 hole cle with a thinned and sharpened skeg
My propshaft is 1/2" above the pad
The power head is a stock block 2.4 200 with cut 5 pedal fiber reeds wmh20 carbs and a light weight flywheel.
Oh there is a extra 130hp at the push of a button.
The prop is a 26 yamaha drag that has been thinned and balanced.
I'm using it strictly for drag racing
The first time I had it out I was just going to take it up and try to keep it on the pad I ended up hitting 82mph within the first 10 minuets.
I haven't been keeping times or speeds yet but will keep this updated.
I have a bunch of props to try and will keep this updated.
Welcome to HydrostreamForums.com
If you're not registered, please consider doing so. It's easy - just click the "Register" link at the top
right corner of the page. Our forum needs members like you to contribute to the site in order to survive.
We are a community of boat lovers and Hydrostream enthusiasts here; we are happy to help anyone
who may need advice or guidance for their 'Stream; and we encourage members to offer their advice
and guidance to others as well. Thank you for visiting our forums, and please register.
We're better than Facebook.
Registering only takes a few minutes and you can do so by CLICKING HERE
If you are a member, don't forget to log in to take full advantage of the forum.
If you're not registered, please consider doing so. It's easy - just click the "Register" link at the top
right corner of the page. Our forum needs members like you to contribute to the site in order to survive.
We are a community of boat lovers and Hydrostream enthusiasts here; we are happy to help anyone
who may need advice or guidance for their 'Stream; and we encourage members to offer their advice
and guidance to others as well. Thank you for visiting our forums, and please register.
We're better than Facebook.
Registering only takes a few minutes and you can do so by CLICKING HERE
If you are a member, don't forget to log in to take full advantage of the forum.
viper set up
viper set up
Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
-
- Site Admin
- Posts: 4001
- Joined: Mar 25, 2009 7:31 pm
- Location: Nowthen, MN
- Has thanked: 363 times
- Been thanked: 86 times
- Contact:
Re: viper set up
Looking forward to any pics and video and the updates. 
[ Post made via Mobile Device ]

[ Post made via Mobile Device ]

-Kevin
Project Vulture | Project Vector | Project Vamp | Project Vixen
The Vulture Wish List | Project CobraJet
1977 HydroStream Vulture - Worlds longest ongoing project.
1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
1976 Pontoon - aka The Family Truckster
Project Vulture | Project Vector | Project Vamp | Project Vixen
The Vulture Wish List | Project CobraJet
1977 HydroStream Vulture - Worlds longest ongoing project.

1982 Hydrostream Vector
1982 Hydrostream Vamp
1973 Hydrostream Vixen
1976 CobraJet Jet Boat - Outboard conversion project
1976 Pontoon - aka The Family Truckster
-
- Regular
- Posts: 215
- Joined: Apr 09, 2009 10:47 pm
- Location: Saginaw, Michigan
- Has thanked: 13 times
- Been thanked: 9 times
Re: viper set up
Your going to have to balance the boat for the nitrous hit, I ran a svs'd 260 with a 125 poke, and if my rhythm was off it was a wild ride. When it was on it was on though. You'll need a cone on the CLE too, or it is going to kick your ***. Been there.


Re: viper set up
You're right about the timing and the bottle. I thought I could just tap it as I went along but found out quick not to do that again. It torques to the left hard as you hit it the to the right as you let off. I found it's best to hit it from the get go and not let up.
The cle has a Titus cone on it already. It was set up for a XR but he went with something else, but thanks for the heads up
Here it is torquing over

The cle has a Titus cone on it already. It was set up for a XR but he went with something else, but thanks for the heads up

Here it is torquing over

Samari on s&f
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
Chet Olson
75 viper 2.4 200, 130 shot of NOS
91 vegas loaned out
79 vking project 2.5 280
-
- Regular
- Posts: 215
- Joined: Apr 09, 2009 10:47 pm
- Location: Saginaw, Michigan
- Has thanked: 13 times
- Been thanked: 9 times
Re: viper set up
I have some other pics around of the hole shot. I ran five inches of set back and launched the boat just a little tucked under, the bow would come up three times then the boat would set. I found it was quicker and easier than dealing with the roll when the bow planted with a lot of negative trim. Took a lot of practice though, when you get it figured out you'll be tough to beat as long as the water/wind stays consistant.
-
- Random Topics
- Replies
- Views
- Last post
-
- 10Replies
- 14149 Views
- Last post by Hippie459MN
Sep 12, 2010 4:27 pm
-
- 1Replies
- 4326 Views
- Last post by Hydrostream Bot
Jun 24, 2010 9:23 pm
-
- 1Replies
- 4418 Views
- Last post by Hydrostream Bot
Jun 24, 2010 9:34 pm
-
- 1Replies
- 4563 Views
- Last post by Hydrostream Bot
Jun 24, 2010 9:35 pm
-
- 5Replies
- 5852 Views
- Last post by silkeysak
Jun 29, 2010 10:04 pm